产品详情
F系列有载分接开关(带滤油)
F系列有载分接开关
F Series on-load Tap-changer
有载分接开关.具有结构先进,动作可靠,使用寿命长,维护方便等优点,适用与50Hz,设备最高电压在40.5kV及以下额定电流在400A及以下的三相油浸式变压器。
This kind of on-load tap-changer has the merits of advanced structure, operating reliably, long useful life and maintenance freely, It is suitable for oil-immersed three-phases transformer with frequency 50Hz, Highest voltage for equipment 40.5KV and below and rated current under 400A and below.
有载分接开关型号含义
Type of on-load tap-changer
有载分接开关调压原理图
On-load tap-changer schematic diagram for voltage regulation
有载分接开关控制器安装尺寸
On-load tap-changer controller installation size
12kV有载分接开关外形安装图
Overall and installation drawing for 12kV on-load tap-changer
12kV有载分接开关线端调压、中部跨接外形安装图
Overall and installation drawing for 12kV line terminal voltage regulation on-load tap-changer
12kV(级电压1000V)有载分接开关中性点调压外形安装图
Overall diagram for 12kV(Step Voltage 1,000V) Neutral point regulation on-load tap-changer
开关型号带A表示开关最大级电压为1000
Vo A-stand for the max. step voltage is 1000 V
12kV(级电压1000V)有载分接开关线端调压外形安装图
Overall and installation drawing for 12kV line terminal voltage regulation on-load tap-changer
1.开关型号带A表示开关最大级电压为1000V;
2.10kV有载开关控制器电缆配长15m.
1.A-stand for the max. step voltage is 1000 V:
2.The length of the cable for 1 0kV on-load tap-changer is 15 Meters
消弧线圈用有载分接开关
The on-load tap-changer are applicable to arc suppression coil
额定电流200A及以下.设备最高电压12kV, 40.5kV.分接位置数7-14级。
It's rated current is 200A and below, the highest voltage of equipment is 12kV and 40.5kV, numbe fo the operation
position 7-14.
FJ 1, -125--200112-15140A
FJ 11-125-y200/40.5-15140A
FD III1-400/10-10090有载分接开关
FD III1-400/10-10090 On-load tap-changer
统一设计40.5kV有载分接开关外形及安装图
Overall and installation drawing for 40.5kV on-load tap-changer in uniform design
40.5kV有载开关控制器电缆配长20m
The length of the cable for 40.5kV on-load tap-changer is 20 Meters
地址:浙江省台州市三门县海润街道凤鸣路3号
产品销售热线:+86-576-83379018 / 83379188
技术咨询电话:+86-576-83379026
传真:+86-576-83379155
邮箱:tl@cntle.com
网址:www.cntle.com
访问手机二维码
腾龙
Copyright © 浙江腾龙电器有限公司 版权所有 浙ICP备13034569号 网站建设:中企动力台州